production
Skip to Content

EM3015: STRESS ANALYSIS A (2016-2017)

Last modified: 28 Jun 2018 10:27


Course Overview

One of the roles of an engineer is to ensure that engineering components perform in service as intended and do not fracture or break into pieces.  However, we know that sometimes engineering components do fail in service.  Course examines how we determine the magnitude of stresses and level of deformation in engineering components and how these are used to appropriately select the material and dimensions for such component in order to avoid failure. Focus is on using stress analysis to design against failure, and therefore enable students to acquire some of the fundamental knowledge and skills required for engineering design.

Course Details

Study Type Undergraduate Level 3
Term First Term Credit Points 15 credits (7.5 ECTS credits)
Campus None. Sustained Study No
Co-ordinators
  • Dr Alfred Akisanya

Qualification Prerequisites

None.

What courses & programmes must have been taken before this course?

  • One of EA2502 Solids and Structures (Passed) or EG2029 Materials and Structures (Passed) or EG2502 Solids and Structures (Passed)
  • Any Undergraduate Programme (Studied)
  • Engineering (EG) (Studied)

What other courses must be taken with this course?

None.

What courses cannot be taken with this course?

  • EG3015 Stress Analysis A (Studied)

Are there a limited number of places available?

No

Course Description

This course focuses on the fundamental relationship between the stresses and strains within engineering components and the load and displacements imposed at their boundaries.  Analytical, experimental and numerical (e.g. finite element method) techniques are used predominantly for 2-dimensional geometries and both elastic and plastic responses are considered.  The concepts of stress equilibrium equations, elastic constitutive laws, and strain-displacement relations are developed and used to obtain the stress solution for a range of commonly used configuration and load cases, including bending, torsion and axisymmetric loading of cylinders and shafts.  The implications of the stress solution are discussed within the context of design against failure. A wide range of mechanical and civil engineering design case studies are presented.

 

Hands-on practical activities are used to enhance students learning.  Students carry out laboratory experiment to determine the stress distribution in an internally pressurised cylinder. The surface strains are measured using a strain gauge rosette at different values of internal pressure.  The principal stresses are then determined using the elastic stress-strain relations, and compared with the theoretical predictions based on both the thin-wall and thick-wall assumptions.   The experimental results and the theoretical results are subsequently compared with those from computer simulation using the finite element method.  The finite element analysis also allows students to assess the limitations of the generally used plane stress assumption for thin-walled cylinders and the implications of stress concentrations at the intersection between the end caps and the main cylinder.   

Contact Teaching Time

Information on contact teaching time is available from the course guide.

Teaching Breakdown

More Information about Week Numbers


Details, including assessments, may be subject to change until 30 August 2024 for 1st term courses and 20 December 2024 for 2nd term courses.

Summative Assessments

1st Attempt: Three-hour written examination paper (90%) and continuous assessment (10%).

The continuous assessment will be based on the keeping of a logbook for the practical work but will take into account attendance and performance in carrying out the practical work.

Resit: Three-hour written examination paper (90%) and continuous assessment (10%).  The continuous assessment mark from the first attempt will be carried forward to the resit.  

Formative Assessment

There are no assessments for this course.

Feedback

a) Assessment grade and feedback comments will be provided on laboratory report within one week of submitting the report.

b) Students can obtain feedback on their understanding of key aspects of the course at the weekly tutorial sessions.

c) One of the tutorial sessions during the half-session will be dedicated to questions and answers on any aspect of the course. The timing of this particular session will be announced at one of the lecture classes.

 d) Students requesting feedback on their exam performance should make an appointment with the course coordinator within two weeks of the publication of the exam results.

Course Learning Outcomes

None.

Compatibility Mode

We have detected that you are have compatibility mode enabled or are using an old version of Internet Explorer. You either need to switch off compatibility mode for this site or upgrade your browser.